Regviz

Freescale Semiconductor /MKE15Z7 /TSI /GENCS

Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text Text

Interpret as GENCS

Share

Cut and paste this URL to share the unmodified register and value:

https://regviz.com/r/Freescale Semiconductor/MKE15Z7/TSI/GENCS#0x0

31 2827 2423 2019 1615 1211 87 43 0 0 0 0 0 0 0 0 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 (0)EOSDMEO 0 (0)EOSF 0 (0)SCNIP 0 (0)STM 0 (0)STPE 0 (0)TSIIEN 0 (0)TSIEN 0 (CLKSOC_SEL)CLKSOC_SEL 0 (RUN_CTRL)RUN_CTRL 0TSI_ANA_TEST 0 (00)DVOLT 0 (0)ESOR 0 (OUTRGF)OUTRGF

EOSF=0, SCNIP=0, TSIIEN=0, DVOLT=00, STPE=0, STM=0, ESOR=0, TSIEN=0, EOSDMEO=0

Description

TSI General Control and Status Register

Fields

EOSDMEO

End-of-Scan DMA Transfer Request Enable Only

0 (0): Do not enable the End-of-Scan DMA transfer request only. Depending on ESOR state, either Out-of-Range or End-of-Scan can trigger a DMA transfer request and interrupt.

1 (1): Only the End-of-Scan event can trigger a DMA transfer request. The Out-of-Range event only and always triggers an interrupt if TSIIE is set.
EOSF

End of Scan Flag

0 (0): Scan not complete.

1 (1): Scan complete.
SCNIP

Scan In Progress Status

0 (0): No scan in progress.

1 (1): Scan in progress.
STM

Scan Trigger Mode

0 (0): Software trigger scan.

1 (1): Hardware trigger scan.
STPE

TSI STOP Enable

0 (0): TSI is disabled when MCU goes into low power mode.

1 (1): Allows TSI to continue running in all low power modes.
TSIIEN

Touch Sensing Input Interrupt Enable

0 (0): TSI interrupt is disabled.

1 (1): TSI interrupt is enabled.
TSIEN

Touch Sensing Input Module Enable

0 (0): TSI module disabled.

1 (1): TSI module enabled.
CLKSOC_SEL

CLKSOC_SEL
RUN_CTRL

RUN_CTRL
TSI_ANA_TEST

TSI_ANA_TEST
DVOLT

DVOLT

0 (00): Vm=0.3V; Vp=1.3V; dvolt=1.0V.

1 (01): Vm=0.3V; Vp=1.6V; dvolt=1.3V.

2 (10): Vm=0.3V; Vp=1.9V; dvolt=1.6V.

3 (11): Vm=0.3V; Vp=2.3V; dvolt=2.0V.
ESOR

End-of-scan or Out-of-Range Interrupt Selection

0 (0): Out-of-range interrupt is allowed.

1 (1): End-of-scan interrupt is allowed.
OUTRGF

Out of Range Flag.

Links

()

Register License

Redistribution and use in source and binary forms, with or without modification,\nare permitted provided that the following conditions are met:\n o Redistributions of source code must retain the above copyright notice, this list\n of conditions and the following disclaimer.\n o Redistributions in binary form must reproduce the above copyright notice, this\n list of conditions and the following disclaimer in the documentation and/or\n other materials provided with the distribution.\n o Neither the name of Freescale Semiconductor, Inc. nor the names of its\n contributors may be used to endorse or promote products derived from this\n software without specific prior written permission.\n THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND\n ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED\n WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE\n DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR\n ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES\n (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;\n LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON\n ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT\n (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS\n SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

 ()

Register Reference

https://github.com/cmsis-svd/cmsis-svd-data